View source for IP Speaker/Add to LumiCenter via External IP

==Description==
This is used in LumiCenter to remotely add an IP speaker and enable audio playback and two-way communication.

==Prerequisites==
* The IP speaker must be on a network with a static public IP address.
* The IP speaker firmware must be version V1.43.1(260522B) or later.

==Step by Step Instructions==

1. Parameters setting for IP speaker:
After logging in, go to Interface Protocol > ONVIF tab > Click on "Enable" button. Configure the Username, Password, ONVIF Port, RTSP Port, RTP Port, NAT IP Address, and NAT ONVIF Port as shown in the images below:<br>
<span style="color:red; font-style:italic;">
Tip: Use 554 as the RTSP port.<br>
Set the RTP port range to 8000–8005 and use UDP for port forwarding.<br>
The NAT IP Address is the network’s static public IP address.<br>
The NAT ONVIF Port is the public ONVIF port used for adding the device.<br>
</span>

[[File:IPSpeakertoLumiCenter1a.png|700px|link=https://wiki.luminyscorp.com/images/a/a0/IPSpeakertoLumiCenter1a.png]]<br>
[[File:IPSpeakertoLumiCenter1b.png|700px|link=https://wiki.luminyscorp.com/images/e/ea/IPSpeakertoLumiCenter1b.png]]

2. Perform port forwarding in advance. The following is an example of the configuration:<br>
<span style="color:red; font-style:italic">
Tip: HTTP port forwarding is optional if remote web access is not required. 
</span>

[[File:IPSpeakertoLumiCenter2a.png|700px|link=https://wiki.luminyscorp.com/images/2/28/IPSpeakertoLumiCenter2a.png]]<br>
[[File:IPSpeakertoLumiCenter2b.png|700px|link=https://wiki.luminyscorp.com/images/9/92/IPSpeakertoLumiCenter2b.png]]

3. Add the IP speaker to LumiCenter by going to Device > Default > Server > Add Devices.<br>
Enter the speaker’s static IP address, ONVIF forwarding port, ONVIF protocol (Generic), and the ONVIF username and password configured in Step 1.<br>
Click the “+” button on the right. After a few seconds, the device will be added. A green status indicates the device was added successfully.

[[File:IPSpeakertoLumiCenter3.png|1400px|link=https://wiki.luminyscorp.com/images/d/d0/IPSpeakertoLumiCenter3.png]]

4. Enable the Speaker and Microphone by selecting them under the added device.

[[File:IPSpeakertoLumiCenter4a.png|700px|link=https://wiki.luminyscorp.com/images/f/f8/IPSpeakertoLumiCenter4a.png]]
[[File:IPSpeakertoLumiCenter4b.png|700px|link=https://wiki.luminyscorp.com/images/d/d3/IPSpeakertoLumiCenter4b.png]]

5. Return to the main page and drag the IP Speaker device into the preview layout. Enable the Speaker and Microphone when you want to use two-way talk; both are disabled by default.

[[File:IPSpeakertoLumiCenter5a.png|700px|link=https://wiki.luminyscorp.com/images/0/0d/IPSpeakertoLumiCenter5a.png]]

<span style = "color: red; font-style: italic">
Tip: If the workstation microphone does not work after being enabled, go to Options > Audio Parameters > Audio Source and ensure the correct option is selected.
Restart the client after changing the audio source.
</span>

[[File:IPSpeakertoLumiCenter5b.png|700px|link=https://wiki.luminyscorp.com/images/1/10/IPSpeakertoLumiCenter5b.png]]

6. Use the audio playback feature to play pre-recorded audio. Go to Device > Default > Server > IP Speaker > Speaker > Audio Path, then click Add, select the File Path, and click OK.

[[File:IPSpeakertoLumiCenter6.png|700px|link=https://wiki.luminyscorp.com/images/9/97/IPSpeakertoLumiCenter6.png]]

7. Click the Test button at the bottom of the Speaker page to play the selected audio file.

[[File:IPSpeakertoLumiCenter7.png|700px|link=https://wiki.luminyscorp.com/images/6/6d/IPSpeakertoLumiCenter7.png]]