Video doorbell/Initial Setup Instructions: Difference between revisions

From Luminys WIKI
Created page with "<div class="lm-banner">File:LuminysMainPageBanner2.png</div> ==Description== This tutorial will go over on how to physically setup the video doorbell. ==Step by Step Instructions== 1. Remove any existing doorbell system(s). Position and level the mounting template on the wall and drill 5 mm holes at the marked points for your selected bracket. 1080px|link=https://wiki.luminyscorp.com/images/3/3e/Vdb_installation_1.png 2. Use the m..."
 
 
(20 intermediate revisions by the same user not shown)
Line 2: Line 2:


==Description==
==Description==
This tutorial will go over on how to physically setup the video doorbell.
This guide provides instructions for configuring your video doorbell for first-time use.
 
==Prerequisites==
*[https://wiki.luminyscorp.com/Video_doorbell/Installation_Instruction Installation instruction]
*[https://wiki.luminyscorp.com/LumiViewer_Mobile_App/How_to_Register_an_Account_in_LumiViewer Register an account in LumiViewer]
*Power on the doorbell and wait for the blue LED indicator to begin flashing.
*Download and open LumiViewer app


==Step by Step Instructions==
==Step by Step Instructions==


1. Remove any existing doorbell system(s). Position and level the mounting template on the wall and drill 5 mm holes at the marked points for your selected bracket.
1. Tap the "+" icon in the top-right corner of the app, then select “SN/Scan.”
 
[[File:Vdb_config_1a.jpg|256px|link=https://wiki.luminyscorp.com/images/3/39/Vdb_config_1a.jpg]]
[[File:Vdb_config_1b.jpg|256px|link=https://wiki.luminyscorp.com/images/3/36/Vdb_config_1b.jpg]]
 
2. Scan the QR code on the product’s serial number (SN). Alternatively, tap the “Manual” button in the top-right corner to enter the SN manually.
 
[[File:Vdb_config_2.jpg|256px|link=https://wiki.luminyscorp.com/images/1/1d/Vdb_config_2.jpg]]
 
3. If you scanned the QR code in the previous step, tap “Next” to continue. If you selected “Manual,” enter the serial number (SN) and then tap “Next” to proceed.
 
[[File:Vdb_config_3.jpg|256px|link=https://wiki.luminyscorp.com/images/d/d7/Vdb_config_3.jpg]]
 
4. Follow the on-screen instructions, then tap “Next” to continue.


[[File:Vdb_installation_1.png|1080px|link=https://wiki.luminyscorp.com/images/3/3e/Vdb_installation_1.png]]
[[File:Vdb_config_4.jpg|256px|link=https://wiki.luminyscorp.com/images/e/e6/Vdb_config_4.jpg]]


2. Use the mounting template to drill a ≥20 mm wiring hole, then tap the wall anchors into the holes until flush. If using the flat bracket, proceed to Step 3. If using the angle-adjustable bracket, go to Step 4.
5. At this step, the following screen will appear. Please wait and keep your phone close to the doorbell.


[[File:Vdb_installation_2.png|1080px|link=https://wiki.luminyscorp.com/images/e/e2/Vdb_installation_2.png]]
[[File:Vdb_config_5.jpg|256px|link=https://wiki.luminyscorp.com/images/0/0a/Vdb_config_5.jpg]]


3. For flat bracket installations, remove and retain the two locking tabs. Align the flat bracket with the wall anchors. Secure the bracket with the supplied flat-head Phillips head screws.
6. Create a password for the doorbell. Providing an email address is optional. Tap "Next" to continue


[[File:Vdb_installation_3.png|1080px|link=https://wiki.luminyscorp.com/images/8/8f/Vdb_installation_3.png]]
[[File:Vdb_config_6.jpg|256px|link=https://wiki.luminyscorp.com/images/2/29/Vdb_config_6.jpg]]


4. For angle-adjustable bracket installations, remove and retain the two locking tabs. Align the angle-adjustable bracket with the wall anchors and secure it using the supplied flat-head Phillips screws. Align the flat bracket on top and fasten it with the supplied round-head Phillips screws.
7. Ensure your phone’s Wi‑Fi is enabled, then tap “Next” to continue.


[[File:Vdb_installation_4.png|1080px|link=https://wiki.luminyscorp.com/images/9/9c/Vdb_installation_4.png]]
[[File:Vdb_config_7.jpg|256px|link=https://wiki.luminyscorp.com/images/3/3a/Vdb_config_7.jpg]]


5. Check the power-supply wire length. If sufficient, proceed to Step 6 and skip step 7. If too short, proceed immediately to Step 7.
8. Enter your Wi‑Fi password, then tap “Next” to continue.


[[File:Vdb_installation_5.png|1080px|link=https://wiki.luminyscorp.com/images/e/e9/Vdb_installation_5.png]]
[[File:Vdb_config_8.jpg|256px|link=https://wiki.luminyscorp.com/images/e/ec/Vdb_config_8.jpg]]


6. If the power supply wires are of sufficient length, connect them to the doorbell terminals and tighten the terminal screws.
9. On this screen, wait without moving your phone too far away from the doorbell. This process may take several minutes to complete.


[[File:Vdb_installation_6.png|1080px|link=https://wiki.luminyscorp.com/images/5/51/Vdb_installation_6.png]]
[[File:Vdb_config_9.jpg|256px|link=https://wiki.luminyscorp.com/images/f/f9/Vdb_config_9.jpg]]


7. If the power supply wires are too short, add the supplied extension using the wire nuts. Connect the extended wires to the doorbell terminals and tighten the terminal screws.
10. Assign a name to the doorbell, then tap “Next” to continue.


[[File:Vdb_installation_7.png|1080px|link=https://wiki.luminyscorp.com/images/c/c2/Vdb_installation_7.png]]
[[File:Vdb_config_10.jpg|256px|link=https://wiki.luminyscorp.com/images/0/03/Vdb_config_10.jpg]]


8. Slide the doorbell onto the bracket. Turn the circuit breaker back on. Plug the wireless chime into a wall outlet.
11. Adjust the time zone and daylight saving time (DST) settings as needed, then tap “Next” to continue.


[[File:Vdb_installation_8.png|1080px|link=https://wiki.luminyscorp.com/images/5/53/Vdb_installation_8.png]]
[[File:Vdb_config_11.jpg|256px|link=https://wiki.luminyscorp.com/images/4/46/Vdb_config_11.jpg]]


9. Insert the locking tab into the gap between the flat bracket and the wall (or angle-adjustable bracket).
12. If this screen appears, the doorbell has been successfully added to your account. Tap “OK” to complete the setup.


[[File:Vdb_installation_9.png|1080px|link=https://wiki.luminyscorp.com/images/3/31/Vdb_installation_9.png]]
[[File:Vdb_config_12.jpg|256px|link=https://wiki.luminyscorp.com/images/a/ae/Vdb_config_12.jpg]]

Latest revision as of 16:55, 8 June 2026

Description

This guide provides instructions for configuring your video doorbell for first-time use.

Prerequisites

Step by Step Instructions

1. Tap the "+" icon in the top-right corner of the app, then select “SN/Scan.”

2. Scan the QR code on the product’s serial number (SN). Alternatively, tap the “Manual” button in the top-right corner to enter the SN manually.

3. If you scanned the QR code in the previous step, tap “Next” to continue. If you selected “Manual,” enter the serial number (SN) and then tap “Next” to proceed.

4. Follow the on-screen instructions, then tap “Next” to continue.

5. At this step, the following screen will appear. Please wait and keep your phone close to the doorbell.

6. Create a password for the doorbell. Providing an email address is optional. Tap "Next" to continue

7. Ensure your phone’s Wi‑Fi is enabled, then tap “Next” to continue.

8. Enter your Wi‑Fi password, then tap “Next” to continue.

9. On this screen, wait without moving your phone too far away from the doorbell. This process may take several minutes to complete.

10. Assign a name to the doorbell, then tap “Next” to continue.

11. Adjust the time zone and daylight saving time (DST) settings as needed, then tap “Next” to continue.

12. If this screen appears, the doorbell has been successfully added to your account. Tap “OK” to complete the setup.

Retrieved from "https://wiki.luminyscorp.com/index.php?title=Video_doorbell/Initial_Setup_Instructions&oldid=54750"